Polyurethane Concrete Seal Epoxy Tile Grout For Swimming Pool , Non
- Single-component without mixing
- Good elasticity, high activity
- Waterproof seal, can be soak for a long time
- The strong cohesive force, contaminate the base material
- Widely use,can be colored
Scope of application
Suitable for all kinds of weather resistance of curtain wall
caulking；Concrete expansion seal；The seal around the door,
window；All kinds of metal, stone, wood, ceramic, most of the
material such as plastic, rubber, tile Or a combination of the
above material is waterproof, soundproof sealing caulking; The
place such as air conditioning pipe sound insulation, heat
preservation seal. Do not apply to the structural sealant and
soaking in swimming pool.
Method of application
Key points of design
1.The seams meet the precondition of telescopic allowance of base
material, the minimum joint width is 5 mm.
2.The depth of range shall be equal to 1/2 of width to width ,
suggest seam's depth not less than 5 mm; For below about 10 mm
width seam , Suggest to be 80% to 100% of width.
3. In order to ensure the sealant to achieve the design activity in
the service period, should use the backing or force protection
4. When designing the joint, should take into account activity
level of the base material and expansion of sealant.
Base plane treatment
Base material surface should be dry, without laitance, dust, or
contaminants. Metal surface should be no oil stain, rusty spot,
color chip which is easy to fall off. Pouring concrete after airing
dry for 28 days. After the rain, outdoor construction need to be
dry for 2 ~ 3 days; The moisture content of base material should be
lower than 9%.
Use brush to remove pollutants, let the juncture place to achieve
the above processing requirements. Backing should choose lever
closed groove polyethylene foam (diameter is about 1.25 times of
the width). If the depth's of the seam is less than the above
requirements, it can use polyethylene force protection band to
replace. When put into the backing should avoid too loose or too
close, putting backing into level position . You can use paper tape
for beautiful , stick the adhesive tape on both sides of the seams,
the tape edge must be aligned with seams. Cut the required size
with 45 °, put the sealant into corresponding glue guns, squeeze
the sealant evenly along the joint, the sealant should fill the
seams full and spill over a little, avoid producing space in the
Using the length (m) of each glue(600ml)
Depth/width 5mm 8mm 10mm 12mm 14mm
6mm / 12.50 10.00 8.33 /
8mm / 9.38 7.50 6.25 5.00
Making the sealant surface become compaction and leveling with a
little water scrape, Repair the sealant into circular concave type
best with appropriate specifications of circular arc convex type
scraper. To get off of paper tape, and check the construction
quality. Don't contact surface of the sealant in 7 hours.
*The above information for general environmental conditions, namely
22 ℃ relative humidity of 55%.
Health & Safety
Without solvent, nonflammable, when used properly is safe. This
product need to prevent frost during storage and transportation.
Protect the eyes and skin. If this product contact with skin, wash
with clean water. If contact with eyes, rinse immediately with
clean water and seek medical care.
Don’t pour into the sewer directly. Sealant can arrange another
time to use. If expired, according to local regulations.
1. Brand Owner’s Authorization Letter is required to be issued
& provided for the corresponding production and exportation;
2. Quality only based on the samples which the buyer provided or
YUNYAN’s counter-sample confirmed by buyer.
In every case, the user alone is fully responsible for any
consequences deriving from the use of the product.
3. OEM MOQ: at least 1*20 feet container per item/color.
Minimum Order Quantity:
Composite paper bag w/. Plastic bag inside